pilotharp17

How to Replace a Kia Sportage Replacement Key For a number of Kia models keys, the key has a keyless entry system built-in. This key usually resembles an electronic remote and can be exchanged with a brand new one from a Kia dealer or a locksmith. Key fobs may stop working for a variety of reasons, such as a dead coin battery, worn buttons or buttons, signal interference, water damage, and a defective receiver module. Here are some suggestions on how you can get your Kia Sportage replacement key to work again. How do you replace the remote key or smartkey? The battery inside your Kia's smart key will eventually need to be replaced, regardless of whether it's a remote key as well as a push-to start key or a normal metal key that does not contain a transponder. This is especially when your car displays a message telling you that the smart or remote keys have low battery power. It's a simple process. To replace the battery in the keyfob, remove your mechanical key from the slit at the back of the fob. Then, pry the cover off. A small screw is inside the key fob to hold the battery in the correct position. By using a small screwdriver remove the screw and pull out the old battery. Then insert the new one and close the hole in the key fob. When the key fob is equipped with an updated battery check it by pressing the locks and unlock buttons. If the doors lock and unlock as expected, then you're all set! You can now use the Kia's hands-free lock/unlock feature when your fingers are cold or you need to do some errands in Brandon. Note: Certain key fobs (transponder chip or smart keys) may require their programming completed. This requires a programing machine that is available only to the automotive locksmith or dealer. Other keys (non-transponder metal keys) don't require programming. If your key requires to be programmed, you will need to be aware of the number stamped on the tag of the key code and record it in a safe place. How do reference replace the battery? If the Kia key fob doesn't respond when you press the lock/unlock button, it's likely that the battery is insufficient. A weak battery can cause other issues like the check engine light flashing on or the engine not cranking. It is fairly easy to replace key fob batteries by using only the use of a few tools. Before beginning the process, make sure that your vehicle is off and all doors are closed. Locate the small plastic piece that is on the bottom of your key fob and move it until a metal key slips out. This key can be inserted into the driver door handle to unlock your car. To replace the battery in the key fob, take off the cover on the rear. Make use of a plastic pry tool to loosen up the latch that holds the black negative cable. Remove the old battery and align the new one in a way that the “+” positive side is facing you and the “–” negative side is facing towards the fob's electrical contacts made of metal. Avoid using excessive force when pushing the new CR2032 into place to avoid damage or bending the metal contacts. After you have installed the new battery then turn the key fob off and on in the ignition until the door locks up. You can then test your Kia's key fob again to make sure it's working as intended. How do you replace a keyless key Depending on the model of the Kia Sportage, you may have an ordinary key fob or a smart key. The difference between these is that the smart fob has tiny mechanical key blade tucked inside it, while the standard fob isn't equipped with. Both key fobs come with a battery that will eventually require replacing. Fortunately, it's an easy task that takes just two minutes. Make sure to shut off your Kia and be on a flat well-lit and well-lit area before you begin. Also, remember that there are tiny pieces inside the fob that can fall out if you are not vigilant. The first step is to locate the small release button that is located on the lower backside of your fob. It will be a circular or rectangular slot. Once you press this the mechanical key blade will pop out and you will be able to open the key fob. After the key fob has been removed, you can remove the battery. The new battery is a one called CR-2032 and can be bought through the internet or at a local auto parts store. After you're done, your key fob should be able to lock and unlock your vehicle, even if it isn't running. How to replace a mechanical key The Kia keyfob is a great convenience that allows us to lock or unlock our car simply by pressing a button. But like any device there are issues with it occasionally. There are ways to fix these problems and keep your key fobs working for the duration of. A dead or low-quality battery is one of the most frequent problems. The fob could be able to cease working or work intermittently. If this is the case try replacing the battery with a fresh new one. If this doesn't fix the problem Try using a standard flathead screwdriver to open the casing of the fob's plastic. Be careful not damage any internal components or scratch the plastic. Once open, carefully remove the old battery and replace it with a brand new one. Close and open the door using the mechanical key. (Every kia fob comes with a spare mechanical key that fits into the slot). Test the key fob to verify that it's working properly. If the key fob isn't working, contact a dealer or locksmith to resolve the problem. To avoid lockouts in the future, ensure you purchase an emergency key that can work in all of the door and trunk cylinders.